CORONAVIRUS (COVID-19) RESOURCE CENTER Read More
do-it-yourself

Toggle Switch Assistive Technology

AbleData does not produce, distribute or sell any of the products listed on this website, but we provide you with information on how to contact manufacturers or distributors of these products. If you are interested in purchasing a product, you can find companies who sell it below.

Toggle Switch Assistive Technology was originally designed for V-LINC, a non-profit of volunteers that specialize in Medical engineering solutions. It was designed for a client who held a position as a telephone operator was sometimes dropping calls that needed to be transferred. The problem was analyzed and the discovery was that the client did not have the dexterity to hold the off-hook button down long enough to guarantee transfer.

The solution involved designing a small 3D printed box that snapped on top of the off-hook button. Inside the box was a large toggle mechanism that snapped in to position by pushing or swiping across the toggle part. The bottom of one side extended enough to push the off-hook button down to engage the switch. The operator can now transfer calls with out trying to hold the button down long enough to transfer a call. Dropped calls became a thing of the past and the special needs client is now successfully performing his duties.

Tools

  • 3D printer
  • Any CAD or modeling software (The author used Blender)
  • Wrench set
  • Small metal cutter for brass rod

Parts

  • One mountable magnet (Neodymium magnet worked well)
  • Two flat Hex head screws (any screws that have or can be filed to a flat surface and sticks to the magnet well)
  • Toggle part (3D printed)
  • Base box (3D printed box) or other surface
  • Mount for desired surface (base box served as mount for toggle)
  • A rod long enough to go through toggle and box (the author used a 3 mm brass rod)
Technical Specifications: 

Step 1: Measurements

For the telephone, the author measured the inside of the frame around the off-hook button, the depth and the location of the switch. For a different kind of project you may need to measure the position of the button switch you want to control, than transfer the co-ordinates to the top plate. You would also need the depth from the top to the button when pressed.

Step 2: Basic Principle

Using a magnet instead of springs has real advantages. It reduces the wear factor and maintenance requirements. It also simplifies the design.

The idea is to align the screws (shown as white dots in the picture above) so that they touch the magnet when toggled forward. They don't have to touch at exactly the same spot but must touch on the magnets strong surface. If the magnet has a hole in the middle be careful not to line up over the hole. The magnet is weaker even with a screw in the hole (metal screw not ideal) .

The two screws in the toggle part should be made of a metal strong enough to feel the pull and snap and hold when tested. The author used a N52 Neodymium bar magnet I had from another project. I aligned both screws to barely touch one side away from the screw in the center of the magnet.

Below is a video of the model alignment. Just make sure each screw face is vertical when the toggle part is in the locked position.

Step 3: Toggle Bar

Use a metal rod to go through the toggle part for strength. The author use a 3 mm brass the length of the box. A nail could be used to secure the structure. Just make the holes large enough to accommodate it. The author threaded the ends in the prototype but found it wasn't necessary in the finale unit. If your holes are lose just heat up the PLA and it will expand to make a tight fit. The rod does not turn so there is not much stress on it. You can add some glue or cover the ends if needed for your application.

Step 4: It Works

The toggle switch created was large enough that one could just swipe it with any part of a hand to flip it in the other position.

Step 5: Assistive Pointer

In case you are interested, the Tee used is a common device for assisting one who has a closed fist or similar constraint. I made one by taking a 4" section of 1" PVC and filling it with scrap PLA; just heat and push into the PVC. Make sure you fill the middle section solid, so the worm screws can set. The author put two holes one on each side and two worm screws, than heated the worm screws with a heat gun and screwed then in. It made a tight fit. You could probably just use one screw or none if you didn't plan to change the pencil out. A regular flat head screw would also probably work; just counter sync to fit flat. Different length pencils are needed for different applications. If you need a bigger tip you can add a pencil top eraser over the pencil.

Available

Price Check
Price: 
0.00
as of: 
08/15/2016
Seller(s): 
Toggle Switch Assistive Technology